Erişim şekli için "info:eu-repo/semantics/closedAccess" Teknik Bilimler Meslek Yüksekokulu listeleme
Toplam kayıt 44, listelenen: 1-20
-
Accuracy Comparison Of Online GNSS PPP Analyzing Web Positioning Services' Performance in Marine Environment
(Compass Publications, Inc, 2016)[Abstract Not Available] -
Analysis of drying of melon in a solar-heat recovery assisted infrared dryer
(Elsevier Ltd, 2016)Infrared drying systems are popular in terms of high heat and mass transfer. By using an infrared dryer, it is possible to catch fast heating and short drying time in comparison to the other drying methods. But it consumes ... -
Analysis of RTK positioning methods comparative study of single-baseline and network RTK
(Compass Publications Inc., 2018)[No abstract available] -
Askorbik asitin MoS2 esaslı elektrotla elektrokimyasal tayini
(Ahmet Yesevi Üniversitesi, 2017)Bu çalışmada, grafen, grafen oksit ve MoS iki boyutlu nanotabakalarına ayrılmak suretiyle 10 farklı kaplama süspansiyonu hazırlanmıştır. Hazırlanan kaplama süspansiyonlarıyla damlatarak-kaplama yöntemi kullanılarak camsı ... -
Behaviour of brick infill walls strengthened with expanded steel plates
(Springer Netherlands, 2016)The present study was dedicated to investigate an effective, economical and convenient method for strengthening brick infill walls, i.e. the use of externally-bonded expanded steel plates. A total of 30 plastered wall ... -
A betonului autocompactant increasing the tensile strength of fiber reinforced self-compacting-concrete, and effects of fiber type and orientation
(Fundatia Serban Solacolu, 2017)In this study, the effects of using fiber in self compacting concrete (SCC) on flow parameters, tensile and compressive strength of concrete were investigated. Unit weight, air content, slump flow, J-ring, V-funnel tests ... -
Bulanık mantık ile nokta konum belirlemede iki boyutlu hata tahmini
(Institute of Electrical and Electronics Engineers Inc., 2019)Gelişen teknoloji ve bilgisayar bilimdeki ilerlemeler insan yaşamını kolaylaştırmayı amaçlamaktadır. Bilgisayar bilimi tarafından geliştirilen her yeni teknoloji sistemlere entegre edilmeye çalışılmaktadır. Hızla gelişmekte ... -
A comparative investigation of the effect of honeycomb core on the latent heat storage with PCM in solar air heater
(Elsevier Ltd, 2019)The aims of this study were to comparatively investigate the effect of using PCM and honeycomb as the internal fin structure in the PCM panel on the thermal performance of solar air heater. The tests performed at six air ... -
A comparative study for accuracy assessment of PPP technique using GPS and GLONASS in urban areas
(Elsevier B.V., 2015)In recent years, the usage of the Precise Point Positioning (PPP) has increased due to its ease of use, providing high accuracy as well as reducing the field operational costs by using only a single GNSS receiver. Moreover, ... -
Deep drawing of polymer coated metal sheets
(Korean Society of Mechanical Engineers, 2019)In the present study, the deep drawing of polymer coated metallic sheets were experimentally investigated to reduce friction and increase manufacturing efficiency without using a lubricant. Coating of metal sheets with a ... -
Design and analysis of quad-band grid array microstrip antenna at UWB and ISM channel frequencies for WBAN operations
(Institute of Electrical and Electronics Engineers Inc., 2018)In this paper, we present design and simulation of a compact grid array microstrip patch antenna. In the design of antenna a RT/duroid 5880 substrate having relative permittivity, thickness and loss tangent of 2.2, 1.57 ... -
Determination of drying kinetics and quality parameters of grape pomace dried with a heat pump dryer
(Elsevier Ltd, 2018)Pomace of Hamburg Muscat was dried at temperature of drying air 45 °C and different air velocity (1.5, 2.0 and 2.5 m/s) in open-loop heat pump (HP) and laboratory-type closed-loop dryer (as a control). In the HP dryer, it ... -
Development of flaw tolerant fiber reinforced cementitious composites with calcined kaolin
(Elsevier Ltd, 2017)Flaws naturally occur in the structure of the cementitious composites or concrete. When brittle composites (ceramics, concrete) are loaded up to their ultimate capacity, micro-cracks initiate and propagate from these flaws ... -
Development of heat pump and infrared-convective dryer and performance analysis for stale bread drying
(Elsevier Ltd, 2016)This experimental study aims to develop a heat pump dryer (HPD) and an infrared dryer (IRD) also the comparative empirical analyses of these two methods and to analyze the drying kinetic of stale bread sliced 15 mm thickness ... -
Drying of grape pomace with a double pass solar collector
(Taylor and Francis Inc., 2019)This study aims to analyze the performance of a novel design of the double pass solar air collector (DPSAC)-assisted drying system and investigate the drying kinetics of grape pomace which is an agricultural by-product. ... -
The effect of 2D-MoS2 doped polypyrrole coatings on brass corrosion
(Elsevier B.V., 2020)Conductive polymers have an important potential against the corrosion applications because they arehighly resistant to chemicals besides they have homogeneous coating properties and transport metals tomore noble regions. ... -
Effect of hyper-plasticizer additive rates on the properties of polypropylene fibre tempered concretes
(Springer, 2018)In this study, effect of different rates of hyper-plasticizer additives on the physical and mechanical properties of polypropylene fibre tempered concretes was investigated. The factors of slump and compaction, which are ... -
Energy, exergy, economic and environmental (4E) analyses of flat-plate and V-groove solar air collectors based on aluminium and copper
(Elsevier Ltd, 2017)An experimental investigation has been carried out to study the effect of energy, economic, and environment of SACs which are smooth and roughened by v-groove protrusions arranged made of copper and aluminium materials. ... -
Experimental analysis of solar air collector with PCM-honeycomb combination under the natural convection
(Elsevier B.V., 2019)Phase change material (PCM) is at the head of materials commonly used in latent heat storage. However, usually the main problem is that the heat conductivity of PCMs is low. Therefore, a novel solar air collector (SAC) ... -
Experimental and numerical analysis of the splay impact on the performance of splayed cross-cut fin heat sink
(Elsevier France-Editions Scientifiques Medicales Elsevier, 2021)In this study, splayed effects on the thermal performance of standard cross-cut heat sink (S-CCHS), fixed-array splayed (FAS-CCHS), and full splayed (FS-CCHS) under natural and forced conditions are studied experimentally ...