Başlık için Makine Mühendisliği Bölümü listeleme
Toplam kayıt 135, listelenen: 86-105
-
Kafes yapı dolgulu hibrit tüplerin enerji sönümleme performanslarının sonlu elemanlar yöntemi kullanılarak incelenmesi
(2019)İnce cidarlı tüplerin enerji sönümleme performanslarının iyileştirmesine yönelik literatürde birçok farklı yaklaşım önerilmiştir. Bu bağlamda farklı tipte malzemeler, kesit geometrileri, desenler vb. önerilmiş ve bu yapıların ... -
Li-doped fullerene pillared graphene nanocomposites for enhancing hydrogen storage: A computational study
(Elsevier, 2021)Hydrogen physisorption in lithium doped fullerene pillared graphene nanocomposites (Li-FPGNs) having tunable pore structures were examined under different temperature and pressure conditions via grand canonical Monte Carlo ... -
The linear stability of the responses of axially moving beams supported by an intermediate spring
(EDP Sciences, 2016)In the present paper, the stability investigation of the linear responses of axially travelling beams supported by an intermediate linear spring is performed numerically by means of searching linear complex eigenvalues. ... -
Low velocity impact response of glass fiber reinforced aluminium foam sandwich
(European Conference on Composite Materials, ECCM, 2012)The aim of this study was the analysis of the bending and the low - velocity impact response of aluminium foam sandwich reinforced by the outer skins made of glass fiber reinforced epoxy matrix and the results were compared ... -
Monitoring and control of PLC based motion control systems via device-net
(Institute of Electrical and Electronics Engineers Inc., 2014)The control of mechanical systems are generally applied by using electric motors which are useful for the control of velocity, position and torque. On the other hand, servo motors are preferred due to their characteristic ... -
A monitoring and control system integrated with smart phones for the efficient use of underground water resources in agricultural product growing
(Hitit University, 2017)Monitoring and control system is very important for crop development process in agriculture zones. A structure which is carried out based on the type of the product with the knowledge of temperature and humidity values of ... -
Monte Carlo simulations of hydrogen adsorption in fullerene pillared graphene nanocomposites
(Taylor & Francis Ltd, 2020)The objective of this study is to investigate the hydrogen storage performances of three-dimensional periodic fullerene pillared graphene nanocomposites (FPGNs) consisting of covalently bonded fullerene units between ... -
Multi-objective crashworthiness optimization of lattice structure filled thin-walled tubes
(Elsevier Ltd, 2020)Thin-walled tubes have been mostly used in passive vehicle safety systems as crash energy absorber. With the use of additive manufacturing technology, it is possible to produce novel filler materials to further enhance the ... -
Multiple objective crashworthiness optimization of circular tubes with functionally graded thickness via artificial neural networks and genetic algorithms
(SAGE Publications Ltd, 2017)The objective of this paper is to develop a multiple objective optimization procedure for crashworthiness optimization of circular tubes having functionally graded thickness. The proposed optimization approach is based on ... -
Nonlinear vibrations of spring-supported axially moving string
(Kluwer Academic Publishers, 2015)In this study, multi-supported axially moving string is discussed. Supports located at the ends of the string are simple supports. A support located in the middle section owns the features of a spring. String speed is ... -
A novel two-layered glass-ceramic sealant design for solid oxide fuel cells
(John Wiley and Sons Ltd, 2017)A thermo-mechanical stress develops on the sealant of an solid oxide fuel cell (SOFC) stack because of thermal expansion coefficient (TEC) differences among ceramic electrolyte, metallic interconnector, and glass-ceramic ... -
A novel two-part interconnector for solid oxide fuel cells
(John Wiley and Sons Ltd, 2014)A two-part interconnector is developed for solid oxide fuel cell stacks to reduce cost and to improve sealing. The novel interconnector involves a metallic core for current collection and gas distribution and a ceramic ... -
Numerical analysis of a commercial display cabinet with air curtain
(2011)Maintaining food temperatures below critical values is the important maximising the high quality display life of chilled foods. Air curtains are especially used in stores and retailer supermarkets as barrier systems to ... -
Numerical investigation of amounts of heat, power and temperature distribution in IT-SOFC
(Electrochemical Society Inc., 2013)In this study, thermodynamic and heat transfer concepts were combined to understanding correlation of heat, power and temperature gradient on the cell. All of heat sources and amounts has been determined for electrolyte ... -
Numerical investigation of heat transfer using impinging jets on triangular and square ribbed roughened walls
(Turkish Society for Thermal Science and Technology, 2017)This paper presents a heat removal study on triangular and square ribbed surfaces under an array of impinging air jets. The investigation was carried out using nozzles with a 7x3 rectangular array of circular jets. The ... -
Optimal design of truss structures using weighted superposition attraction algorithm
(Springer, 2020)In this paper, a recently developed swarm based metaheuristic algorithm called weighted superposition attraction (WSA) is implemented for sizing optimization of truss structures first time in literature. The WSA algorithm ... -
Performance investigation of an eight cylinder gasoline engine
(American Society of Mechanical Engineers (ASME), 2014)Performance investigation of a Chevrolet 5.7, eight cylinder gasoline engine is experimentally carried out at laboratuary conditions by means of the special softwares called "NetDyn" and "WinDyn". This experimental work ... -
Physical properties of LLDPE and PP filled with wood flours
(American Society of Mechanical Engineers (ASME), 2015)In this study, composites of polypropylene (PP), as well as linear low density polyethylene (LLDPE) thermoplastics filled with wood flour have been investigated to study the effect of size and amount of wood flour on their ... -
Predicting energy absorption parameters of aluminum lattice structures filled tubes via artificial neural networks
(2019)In this paper, the energy absorption parameters of aluminum body centered cubic lattice structures filled thin-walled tubes under axial loading are predicted via artificial neural networks (ANNs). Different tube thickness, ... -
Predicting microstructure evolution during directed energy deposition additive manufacturing of Ti-6Al-4V
(American Society of Mechanical Engineers (ASME), 2018)Laser engineering net shaping (LENS) is one of the representative processes of directed energy deposition (DED) in which a moving heat source having high-intensity melts and fuses metal powders together to print parts. The ...